Write a review
Evaluations will be activated after verification.

The fields marked with the asterisk * are mandatory.
Clicking on "Save" I accept the processing of my personal data in accordance with the Privacy statement of SCOOTER CENTER GmbH.

 
 
Item successfully added.

Rear brake hub 10 inch -OEM QUALITY- Vespa PX (1984-), T5 125cc - oil seal 30mm

4350053
Rear brake hub 10 inch -OEM QUALITY- Vespa PX (1984-), T5 125cc - oil seal 30mm
Rear brake hub 10 inch -OEM QUALITY- Vespa PX (1984-), T5 125cc - oil seal 30mm
Rear brake hub 10 inch -OEM QUALITY- Vespa PX (1984-), T5 125cc - oil seal 30mm
Rear brake hub 10 inch -OEM QUALITY- Vespa PX (1984-), T5 125cc - oil seal 30mm

Description


OEM-QUALITY
brake drum in very good quality. A fine cast aluminium, which has already proven its racing suitability, makes this drum our favourite. Unbeatable in price, performance AND quality! The brake drum studs are cast-in.

LML
original LML brake drums, manufactured for the Indian licensed buildings of PX. Good and cheap replacement for the often very expensive original parts. Has a diameter at the shaft seal running surface of 30mm. The drum can therefore be used on PX and T5 models built from 1984 onwards. The brake drum studs are cast-in.

FA ITALIA
brake drums Made in Italy. For normal loads, as occurring with standard vehicles, a good and cheap solution for everyday use. For racing or very powerful engines we recommend the OEM QUALITY brake drums. The brake drum studs are cast-in.

PIAGGIO
Piaggio delivers again and again rear brake drums from changing production, partly in, for Piaggio conditions, unfortunately inferior quality. The drum does not have a ground shaft sealing ring surface and can only be used with a felt ring. The brake drum studs are cast-in.

Background knowledge:
With the introduction of the Vespa GL around 1962 a new type of brake drum for the rear wheel shaft was established, which is still used today in almost the same design. With the exception of the GS160/SS180 and COSA models, this drum type was installed in all Vespa scooters from 1962 on with horizontal cylinder (Vespa Largeframe).

  • 1962-1984: drum with Ø27mm oil seal running surface, crown nut secured with split pin. Tightening torque: 75-90NM
  • 1984-1988: Drum with Ø30mm oil seal running surface, hexagon nut secured with cage and split pin. Tightening torque: 90-110NM
  • 1988-today: Drum with Ø31,5mm unground running surface for felt ring, hexagon nut with cage and split pin secured (the actual shaft seal is located in the gearbox). Tightening torque: 90-110NM

The continuously increasing flange diameter (from Ø27 to Ø31.5mm) allows a much more stable brake drum flange. The models with only Ø27mm tend to expand quickly if the tightening torque was too low. A spread brake drum flange can be recognized by a rear wheel that keeps loosening, despite a correctly tightened rear wheel nut. In this case only a timely replacement of the brake drum can help, otherwise the toothing of the main shaft is affected and must also be replaced. For stability reasons it is always recommended to change to a drum with at least 30mm flange diameter.

UPGRADE old to new (27 > 30/31,5mm): The more stable drum of the PX Lusso models from 1984-1988 can also be used on the older years of manufacture with Ø27mm drum, provided that the shaft seal ring of the Lusso models with Ø30mm and the washer of the models from 1984 onwards are also used there. With a fully enclosed rear wheel bearing (6204 2RS) a brake drum of the models from 1988 up (with Ø31,5mm felt ring) can also be used without a shaft seal. here please check the bearing for tightness in regular intervals.

DOWNGRADE new to old (31,5 > 30mm): The newest type (1988-today) has no ground running surface and is therefore unsuitable for the combination with a shaft seal. The Lusso drum from 1984-1988 can also be used here and converted to a conventional shaft seal. If the internal shaft sealing ring is omitted here, make sure to close the drip hole in the housing.

(US)


AI-translation

 
This item is currently not available.
€41.95 *

incl. VAT plus shipping costs

The item is ordered and will be in stock soon
P For this item you get fidelity point/s
OEM numbers (for comparison purposes only)
Piaggio 194433, E.4335, E4335
Please inform me once the product is available again.
Customers alternatively searched for
Bremstrommel | Hinten | Trommel | Bremse | Rear | Brake | Hub | Tambour De Frein Arrière | Tamburo Freno Posteriore | Tambor De Freno Atrás |

Ratings


21 Aug 2017

good price quality

18 Oct 2016

Excellent

17 Oct 2016

Good

15 Apr 2016

Gute preis leistung

18 Aug 2015

Passt und funktioniert

7 Aug 2015

Gute Qualität

9 Jun 2015

Sitzt, passt, wurde schnell geliefert und macht was sie soll. Richtig gut bremsen!

4 Jun 2015

Guter Standard.

6 Nov 2014

Produkt wie beschrieben.

Alternative items


Rear brake hub 10 inch -LML- Vespa PX (1984-), T5 125cc - oil seal 30mm
LML
3330912
LML
Rear brake hub 10 inch -LML- Vespa PX (1984-), T5 125cc - oil seal 30mm
The item is ordered and will be in stock soon
€49.94 *
*incl. VAT plus shipping costs
Rear brake hub 10 inch -FA ITALIA- Vespa PX (1988-), T5 125cc - felt ring 31.5mm
Fa Italia
3331774
Fa Italia
Rear brake hub 10 inch -FA ITALIA- Vespa PX (1988-), T5 125cc - felt ring 31.5mm
Available immediately (delivery time 1-3 working days*)
€88.95 *
*incl. VAT plus shipping costs
Rear brake hub 10 inch -FA ITALIA- Vespa PX (1984-), T5 125cc - oil seal 30mm
Fa Italia
3331776
Fa Italia
Rear brake hub 10 inch -FA ITALIA- Vespa PX (1984-), T5 125cc - oil seal 30mm
Available immediately (delivery time 1-3 working days*)
€69.95 *
*incl. VAT plus shipping costs
Recently viewed items