Write a review
Evaluations will be activated after verification.

The fields marked with the asterisk * are mandatory.
Clicking on "Save" I accept the processing of my personal data in accordance with the Privacy statement of SCOOTER CENTER GmbH.

 
 
Item successfully added.

Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special

9077011SVT
Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special
Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special
Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special
Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special
Wiring loom set for conversion (incl. light switch) -BGM PRO, Vespa AC conversion to electronic ignition (Vespatronic) - Vespa Smallframe V50 Special

Description


Conversion wiring harness for conversion to:
  • Vespatronic ignition system in 50N Special with indicator (angular steering head)
  • The conversion to a more modern alternator/ignition type is a proven means to be more durable and safer on the road. The contact-free CDI ignitions are almost indestructible and reliable, and the light output with a modern, regulator-supported, on-board electrical system is many times higher, since not only is the voltage increased from 6Volt to 12Volt, but the ignition base plate can also produce more power in general.

    Therefore it is necessary to adjust the wiring harness, because in modern electrics the alternators have all light coils connected in series for maximum power output and only one live cable is left as output for the on-board voltage. This is then led to the voltage regulator, which limits the on-board voltage to constant 12-13Volt. This effectively prevents the dreaded domino effect of the old electrical system, where all bulbs burn out one after the other after a defect of one. Only after the regulator is the current then conducted to the individual consumers. By this technology also a very high performance alternator can be used like e.g. our BGM ignition base plate, which already guarantees a high light yield and ignition performance at low speeds.

    To use such an alternator in the old chassis one needs therefore a suitable wiring harness. Our retrofit wiring harness is exactly the right thing and can be used very universally. It is based on an electrical system reduced to the most necessary, which lights the horn/ratchet, headlights/dipped headlights and the rear/brake lights. Optionally, the installation of a flasher relay is possible, the wiring harness is already prepared for this.
    In connection with our BGM 12Volt voltage regulator, this results in a very modern on-board electrical system which, in addition to a brilliant and powerful light output, also has gimmicks such as a DC output for the charging function of a mobile phone or e.g. a navigation device.

    By using our conversion wiring harness, no battery is needed anymore. A possibly existing 6V ratchet can still be used, it can cope with the occasional 12V without problems. Further technical information is stored in our wiring diagram.

  • reliable electronic ignition - never again adjust contacts
  • very high light output with 12V on-board voltage
  • optional direct current for the charging function of a mobile phone, navigation device

  • Please note: With very old vehicles space problems may occur due to the larger cable cross-sections of the conversion wiring harness used. This especially in the area of the tube duct for the rear light and in the steering head area. For safety reasons we do not want to use smaller cable cross sections.
  • Wiring diagram: See "Downloads"
  • Available as set with matching light switch for:

    • Vespa Smallframe V50 Special
    • Vespa Smallframe V50, 50N, PV125, ET3, Vespa Largeframe Sprint, Rally, TS, GT, GTR, GL, Super, GS160, SS180, VNA, VNB, VBA, VBB

    Note: This type of wiring harness already includes a pre-wired light switch. Therefore, the wiring for the handlebars (for wiring light switches with screw terminals) is unnecessary and does not need to be mounted.

    A brake light switch type "normally open" is required.

    (US)


    AI-translation

     
    €80.00 *

    incl. VAT plus shipping costs

    Available immediately (delivery time 1-3 working days*)
    P For this item you get fidelity point/s
    General
    EAN: 4251389106319
    Customers alternatively searched for
    Umrüstkabelbaum | Kabelbaum | Set | Kabelstrang | Kabelsatz | Kabelset | Fahrzeugelektrik | Bordelektrik | Rollerelektrik | Zündaussetzer | Elektronikprobleme | Elektrikprobleme | Schwaches Licht | Schlechtes | Helles | Helleres | Umrüstung | Conversion | Wiring | Loom | Faisceau Électrique | Kit Impianto Elettrico | Mazo |
    Conversion wiring harness for conversion to: Vespatronic ignition system in 50N Special with...Continue reading

    Fits the following vehicles


    Recently viewed items