Write a review
Evaluations will be activated after verification.
Item successfully added.
Ignition -BGM PRO stator HP V2.0 (electronic ignition)- Vespa Sprint150 (VLB1T), TS125 (VNL3T), GT125 (VNL2T), GTR125 (VNL2T), Super, GL150 (VLA1T), VNA, VNB, VBA, VBB
Part no.:
BGM8032
Description
Latest version of the proven BGM PRO HP (High Power) ignition base plate for the conversion from contact ignition to electronic ignition.
Suitable for e.g. Vespa VNA,VNB, VBA, VBB, GL, Super, Sprint, GT, GTR, TS, Rally
BENEFITS ELECTRONIC IGNITION
Specially developed for the conversion of contact controlled engines to
Maintenance-free electronic ignition.
After conversion, the former weak 6Volt on-board power supply system has a powerful 12Volt light output. The previously self-regulating electrical system is converted to a reliable and bulb-friendly regulator control (e.g. with BGM6690). The high-quality wiring ensures a safe transmission of the high light and ignition power. With its high wattage, it already provides a very good light output when idling, which does not diminish even when using the indicators or additional power consumers. Maintenance work, as usual with contact ignitions, is not necessary.
ADVANTAGES BGM PRO HP In contrast to a Vespa PX ignition base plate the BGM Pro HP has a longer cable load to be able to mount the ignition base plate also on older vehicles perfectly. In addition it has an adapted base plate contour to fit perfectly on engines before 1977 (with a larger shaft seal seat than PX). NOTE The BGM pickup has a nominal resistance of 100 Ohm (+/- 10Ohm) BENEFITS SILICONE CONDUCTS CONVERSION TO ELECTRONIC IGNITION Everything necessary for this is available individually or as a set. FIT FOR OTHER NECESSARY COMPONENTS Also as a set for conversion (BGM6661PRO) BITTE BEACHTEN
BGM has revised the thousandfold proven BGM Pro ignition base plate and made it even better.
Special attention was paid to a very high quality of the coils and the pickup.
In addition, the wiring was changed to textile-sheathed silicone cables.
A special gimmick is the cord already attached to the cable branch for easy insertion of the cable harness through the cable channel in the engine housing.
Compared to a conventional electronic ignition, the BGM Pro HP ignition base plate has specially combined coil windings.
When converting from contact ignition to this base plate, the use of a different fan wheel, a voltage regulator and a CDI is necessary.
A standard old voltage regulator, like the standard ignition coil, is no longer needed.
With the BGM voltage regulator BGM6690 a battery (12Volt battery required) can be charged while driving. The old wiring harness can still be used, but the formerly individual circuits must be combined here, because the voltage regulator only offers one output for the complete power supply. It is easier to convert to one of our conversion wiring harnesses (e.g. 9077011).
The BGM ignition base plate fits all Vespa engines of the large frame models with rotary vane intake control, e.g.e.g. Vespa VNA, VNB, VBA, VBB, VLA, GT, GTR, Sprint, Rally, PX, LML 2T, Bajaj Chetak.
The alignment of the crankshaft in the engine housing, and thus also the position of the pole wheel, is significantly more variable in the old large-frame engines (recognizable by crankshaft bearings of the same size with 25x62x12mm) than z.The crankshaft bearings are not fixed in the engine housing by a circlip, but are only fitted in the housing with a slight press fit. Due to various tolerances (e.g. the width of the shaft sealing rings, worn bearing seats, orientation of the cone on the crankshaft) there may be significant deviations from the originally intended positioning of the shaft in the crankcase. Prerequisite for a correctly working ignition is a perfect alignment of the pole wheel with the ignition base plate. Otherwise the trigger surface in the pole wheel will not run parallel to the pickup, which can lead to misfiring. If the ignition does not produce a spark, the fault is usually to be found here. For easy repair we offer distance plates (BGM8000S05) for the pickup on the ignition base plate. With this the correct distance can be restored in a simple way.
AI-translation
This item is currently not available.
€99.00 *
incl. VAT plus shipping costs
The item is ordered and will be in stock soon
P
For this item you get
fidelity point/s
| General | |
|---|---|
| EAN: | 4251389104230 |
| Ignition stator plate | |
| ignition type: | electronic |
| tension: | 12V |
| current: | alternating current (AC) |
| type of rotor for stator: | external rotor |
| position (pickup / points): | internal |
| number of coils: | 5 |
| diameter stator: | 115 mm |
| diameter coils: | 93 mm |
| total height: | 46 mm |
| number of wires: | 5 |
| type of plug connector: | single plug connector |
| Rotor | |
| rotor type: | external rotor |
| Ignition | |
| ignition timing: | fixed |
| rotor incl.: | |
| CDI incl.: | |
| voltage regulator: | |
Please inform me once the product is available again.
| Customers alternatively searched for | |
|---|---|
| Zündung | Lichtmaschine | Lima | Lichtmaschiene | Grundplatte | Zündgrundplatte | Zündungsgrundplatte | Ankerplatte | Zündanker | Zündankerplatte | Zündplatte | Ruckeln | Zündaussetzer | Zündungsprobleme | Zündungsaussetzer | Zündfunke | Funke | Schwacher | Ignition | Ignite | Bad | Spark | Detonation | Allumage | Statore Accensione Completo | Encendido | Estator | Stator | | |
Related items
Recently viewed items