Write a review
Evaluations will be activated after verification.

The fields marked with the asterisk * are mandatory.
Clicking on "Save" I accept the processing of my personal data in accordance with the Privacy statement of SCOOTER CENTER GmbH.

 
 
Item successfully added.

Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc

PN26482025
Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc
Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc
Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc
Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc
Engine casing -PINASCO Slave, reed valve intake- Vespa T5 125cc

Description


The Pinasco motor housings are very high-quality replacement motor housings made of the finest die-cast aluminium. In addition to the very precise machining, they also offer many special features that are particularly interesting for tuners.
In addition to the significantly larger sealing surfaces at the cylinder base and carburetor inlet, Pinasco also offers the housings as a version with diaphragm inlet. This intake technology, which has long been a standard in the automatic sector, offers even large carburettors a good passage to breathe deeply. Further reinforcements in the casting, a larger crankshaft bearing as well as the great scope of supply round off the superbe overall picture of the Pinasco engine housing perfectly.

The housings are manufactured in two versions:
MASTER = SLAVE = MEMBRANE CONTROLLED

The engine internals and ignition components of all 125-200cc models from 1982 onwards can be used. The components from model year 1984 onwards are preferable due to the improved and more stable transmission and the more powerful alternator. The engine of the COSA models is also well suited as a donor engine. Their engine block is different on the outside, but uses the same internals as the PX models from 1992 onwards.

Both versions have the same useful improvements:

  • MATERIAL
    High quality die-cast aluminium with fine surface finish
  • SEALING SURFACES br /> Very precisely milled sealing surfaces
  • STRENGTHENER br /> stiffening ribs in the area of the main shaft bearing on the control panel side and the shock absorber support
  • MASSIVE
    Significantly more material in the area of the cylinder base sealing surface and the carburettor inlet
  • Shaft seal ring
    The housings are manufactured to accommodate a metal shaft seal ring (clutch side). Here please always use the version for the 200cc versions with brown sealing lip.
  • FIT
    Two additional fitting bushes = crankshafts with extra long stroke can do without the centering edge of the lima half. Dimensions bushes AØ=9,95mm, IØ=8,40mm, h=13,80mm
  • GUMMIS
    The drillings for the large silent rubbers are Ø=44mm (original Piaggio Ø=43mm).
    The enclosed silent rubbers are stiffer and offer a better guidance of the engine in the frame.
    Piaggio silent rubbers also fit. Solutions with metal bushings or without preload do not usually fit if they are made for Piaggio motor housings (Jockey, PLC).The motor housings do not have a stamped motor number or prefix
  • NUMBER
    The motor housings do not have a stamped motor number or prefix
  • OIL DRILLING
    No drip hole for gear oil = The nonsensical drip hole indicating whether the internal shaft seal is defective has been omitted*.

*Our tip: Run sealed bearing and external shaft sealing ring with corresponding brake drum.


SPECIAL FEATURES ROTARY SLEEVE VERSION
- Extra large sealing surface over both motor halves, suitable for all intake manifolds
- Can be used as a 1:1 replacement for an original motor housing
SPECIAL FEATURES MEMBRANE VERSION
- Central, full-surface diaphragm inlet
- Incl. Membrane suction port, incl. Diaphragm in RD350 format (perforated 58x48mm)
- Rubber intake rotatable 360°, connection width carburettor= Ø34mm
- Rubber suitable for Keihin PWK28, Mikuni TMX27/30, Dell'Orto PHBH28/30, VHS24- 30
- No shaft for oil pump control cast in
- No bore for oil pump drive

The enclosed fitting bush for the auxiliary shaft must be inserted by yourself
If other gear components than those of the PX models from 125cc on are to be used, please check the auxiliary shaft axis for compatibility beforehand and if necessary
Please use high-strength adhesive for all studs. The cylinder studs do not have a one-sided oversize as is usual with Piaggio. Therefore, glue in the Pinasco cylinder studs supplied. We recommend that all threads be cut and cleaned with compressed air.
ASSEMBLY NOTE:
The alternator-side crankshaft bearing NU205 is not flush with the engine housing.
It protrudes approx. 1mm in the direction of the crankshaft.

COMPLISHINGS

- ROTARY VALVE
- All stud bolts
- Silent rubbers + washers for silent rubbers
- housing seals
- bushing for auxiliary shaft axis

- MEMBRANE
- as above, additionally included:
- Intake manifold incl. diaphragm, intake rubber, gasket and small parts
- NOTE: No screws for fastening the intake manifold to the engine block are included (see: Accessories)

(US)


AI-translation

 
This item is currently not available.
€869.00 *

incl. VAT plus shipping costs

The item is ordered and will be in stock soon
P For this item you get fidelity point/s
OEM numbers (for comparison purposes only)
Pinasco 26482025
Please inform me once the product is available again.
Customers alternatively searched for
Motorgehäuse | Motorblock | Gehäuse | Block | Casing | Triebwerksschalen | Schalen | Motorschalen | Motorhälfte | Motorhälften | Gehäusehälfte | Gehäusehälften | Engine | Engine Casing | Crankcase | Crank Case | Motor Case | Carters Moteur | Carter | Cárter Motor |
The Pinasco motor housings are very high-quality replacement motor housings made of the finest...Continue reading

Ersatzteile


Crankcase gasket set -PINASCO Master + Slave- Vespa PX - also suitable for Pinasco 251
Der Dichter
3331850
Der Dichter
Crankcase gasket set -PINASCO Master + Slave- Vespa PX - also suitable for Pinasco 251
Available immediately (delivery time 1-3 working days*)
€28.91 *
*incl. VAT plus shipping costs
Gasket set for reed valve intake -PINASCO- Vespa PX
Der Dichter
3331854
Der Dichter
Gasket set for reed valve intake -PINASCO- Vespa PX
Available immediately (delivery time 1-3 working days*)
€10.95 *
*incl. VAT plus shipping costs
Recently viewed items