Write a review
Evaluations will be activated after verification.

The fields marked with the asterisk * are mandatory.
Clicking on "Save" I accept the processing of my personal data in accordance with the Privacy statement of SCOOTER CENTER GmbH.

 
 
Item successfully added.

Engine repair kit -LAMBRETTA XXL- Lambretta LI, LIS, SX, TV (series 2-3), DL, GP

3333089MB
€356.90 *

incl. VAT plus shipping costs

The item is ordered and will be in stock soon

Type:

Please inform me once the product is available again.
P For this item you get fidelity point/s
Engine revision set Lambretta XXL We offer you two revision sets for your Lambretta engine. In...Continue reading

Description


Engine revision set Lambretta XXL

We offer you two revision sets for your Lambretta engine. In the large set you will find all the parts you need to fit a bare motor housing with bearings, studs, shaft seals, silent blocks and bushings. Or to completely rebuild an old motor housing.

Included in delivery:

1. complete motor bearing set and bearing bushings dl/GP. It can also be used for the Li/SX models if the distance ring is not installed in the maghousing. So the wider NU2205 bearing of the dl/GP also fits the earlier models.

  • 6305 ball bearing drive side crankshaft - SKF or FAG

  • NU2205 ball bearing alternator side - SKF or FAG

  • ball bearing rear wheel - bgm PRO

  • 6004 Ball bearing auxiliary shaft - SKF or FAG

  • Coupling bushing dl/GP - bgm PRO

  • Needle bearing -K- (24x28x10 mm) Spider/pinion LI/SX/TV/GT (2 pieces) - SKF or FAG

  • Needle bearing -K- (16x22x12 mm) Auxiliary shaft/motor housing - SKF or FAG

  • Needle bearing -K- (20x24x10 mm) Main shaft/gear cover plate - SKF or FAG

  • Bearing bush Auxiliary shaft

  • Washer Auxiliary shaft

  • Washer Needle bearing Main shaft/gear 1.

2. Complete engine gasket set - 29 parts. Fits 125, 150, 175 and 200 ccm.

3. Seegeringset MB Developments. All sea ring rings used except those in Maghousing (Art. No. 8002140).

4. Complete O-Ring Set MB Developments. For main shaft, rear brake arm, shift and clutch shaft.

5. All bushings: Shift shaft, kick starter inside and outside.

6. All motor studs, dowel pins, grease nipples:

  • Complete stud bolt set motor cover suitable for series 1-3 - bgm PRO

  • Complete stud bolt set Gear cover plate - MBD

  • Stud bolt M6 x 25 mm Fan wheel housing - 3 pieces

  • Stud bolt M6 x 21 mm Cover plate Rear wheel bearing - 4 pieces

  • Stud bolt M6 x 28 mm Chain tensioner - 2 pieces

  • Fitting pins Motor housing and gear cover plate - 4 pieces

  • Grease nipple M8 x 1,25 Brake arm - 1 piece

7. Disk kickstarter shaft MBD in 1.0 mm and 1.5 mm to distance the kickstarter shaft on the outside of the engine cover

8. Kickstarter piston bolt MB Developments

9. Silent block set bgm PRO

10. Pressure plate set for chain tensioner.

11. Screw hexagon socket M6 x 16 mm (4 pieces) for fixing the cover plate for the 6305 bearing on the drive side.

12. L-ring fan wheel housing

13. All oil screws: check, drain, vent - Casa Lambretta

14. screw M6 x 18 mm -ISO 7380- with flat hexagon socket head for fixing the shift fork plus M6 spring washer corrugated

15. gear compensating washers bgm PRO in 2.00 mm, 2.20 mm and 2.40 mm and 2.60 mm.

16. clutch nut M14 x 1.5

17. Coupling nut locking plate

18. Coupling compensating washers set bgm PRO (0.8 mm, 1.0 mm, 1.2 mm, 1.4 mm and 1.6 mm)

19. Switching spring SIL

20. Switch ball Ø=7,9 mm - 2 pieces

b>21. Halfmoon wedge Fan wheel

22. Cable clamping plate in maghousing - MBD

23. Screw set Maghousing/Cylinder cover - MBD

24. M6 washers - 100 pieces - in 100er set cheaper

25. M6 stop nuts - 100 pieces - cheaper in 100er set

With the shaft seal set you can choose between MB Developments (inner crankshaft seals made of FPM), Jockeys Boxenstop (inner crankshaft seals made of FPM) and Casa Lambretta (all shaft seals made of FPM).

Some parts are not included in the set, because the choices are too big. This applies to clutch revision parts, front sprocket, chain tensioner, chain, 6305 bearing cover plate, cylinder stud, kick starter shaft, shift claw and engine adjusters.



(machine-translated)
 

Fits the following vehicles


  • Eibar Lambretta LI 150 (series 2)
  • Innocenti Lambretta GP 150 (DL 150)
  • Innocenti Lambretta GP 200 (DL 200)
  • Innocenti Lambretta LI 150 (series 2)
  • Innocenti Lambretta LI 150 (series 3)
  • Innocenti Lambretta LI 150 Special (LIS 150)
  • Innocenti Lambretta TV 200 (GT 200)
  • Innocenti Lambretta SX 150 (X 150 Special)
  • Innocenti Lambretta SX 200 (X 200 Special)
  • Serveta Lambretta Lince 150
  • Serveta Lambretta Scooterlinea 150
  • Serveta Lambretta Special 150
  • Serveta Lambretta Jet 200
  • Serveta Lambretta Lince 200
  • Serveta Lambretta Scooterlinea 200
  • SIL Lambretta GP 150
  • SIL Lambretta GP 200
Read, edit and discuss reviews...Continue reading

Alternative items


Other customers also viewed the following items


Recently viewed items