PERFORMANCE
The clutch is supplied ready for installation and is tuned for a power range up to approx. 20PS / 22Nm by means of the mounted clutch springs. Reinforced springs (available separately, BGM PRO XXL) extend the power range of the clutch to over 40 HP. At the same time it still remains easy to operate.
VEHICLES
The bgm PRO Superstrong 2.0 CR replaces every conventional type of clutch as used in the
Vespa large frame models with inlet rotary vane control from about 1967 onwards.
Usable in Vespa GL, Super, Sprint, Sprint Veloce, GT, GTR, TS, Rally, PX, Cosa and T5.
MODIFICATIONS COVER TYPE CR TOOTHINGS transmission primary wheel primary wheel originally installed in Usable BGM Superstrong 2.0 CR couplings 62Z* x 23Z*, 24Z*, 25Z* (straight toothed) 63Z* x 24Z*, 24Z*, 25Z* (straight toothed) 65Z Rally200, PX200 22Z*, 23Z, 24Z* 67Z All 125-180cc models up to year of manufacture 1977 20Z , 21Z , 22Z, 23Z* 68Z All 80-150cc models from year of manufacture 1978, all Cosa 20Z , 21Z , 22Z, 23Z* *BGM pinions with special gearing examples RECOMMENDATION (US8719)
Vehicles with less than 180ccm (ex works) require the clutch cover of the 200ccm models, unless the original existing clutch cover is to be modified.
We deliver the Supertrong 2.0 CR with the clutch facing type of the Honda CR80/VFR400.
These have a larger effective radius, less weight, wider plates and a very resilient facing material. The advantages are a lighter clutch, which separates faster and is still extremely resilient. The traditional cork linings with a wide contact surface offer no advantages whatsoever, which is why we no longer use them in the Superstrong 2.0 CR.
Clutches with straight-toothed pinions can only be combined with the corresponding straight-toothed primary wheel. To do this, the motor must be fully opened. The extra long primary reduction ratios based on the 62/63 tooth primary gear are only available with straight teeth. The high torque of motors requiring such a long reduction is transmitted directly to the gearbox via straight teeth without exerting lateral forces on the auxiliary shaft bearing. Due to the precise manufacturing process, the straight-toothed drives are nevertheless just as quiet as the helical-toothed drives.
A primary drive consists of a clutch (pinion) and primary gear.
Piaggio has 65, 67 and 68 teeth primary gears already combined ex works with different clutch pinions.
Due to the different so-called gear modules, the following wheel/pinion combinations can be used.
Please note: BGM is the only manufacturer to offer different 22Z pinions for 67/68Z and 65Z primary gears. This is the only way to guarantee maximum stability.
For the greatest possible gear ratio range, simply install the special BGM 64 tooth primary wheel (motor must be completely opened for this). Then, by simply changing the clutch pinion, the engine can be reduced in size to suit a tame 177cc cylinder up to a torque steamer.
Engines with a lot of torque and early power peak choose the straight-toothed clutches that also require a straight-toothed primary wheel (also available as a set). This allows very long gear reductions to be achieved. Ideal even if the overall gear ratio is too short for very sporty engines with a modified auxiliary shaft and shorter gear steps (e.g. MHR). Also an option if the actual gearbox is very short (PX80) or the gear ratio is too low due to a small wheel diameter (PX200 engine with 8 inch tyres in Oldie).
The scope of delivery includes the complete ready-to-install clutch with bgm PRO Cosa clutch facings and ten BGM PRO XL springs. A new O-ring for the clutch cover, the half moon wedge and a new clutch nut are also included. We use a nut with clamping part (MBN13023, T2, strength class 10, DBL9440.40) as we have had the best experience with this nut in racing with over 40PS shaft power. Tightening torque 70-75NM. We do not recommend other safety devices such as Nordlock, corrugated spring washers (DIN137) or serrated lock washers (DIN6798).
We also recommend a low-alloy gear oil of the classes API GL3/GL4 for high performance engines to avoid slipping of the clutch even under extreme loads. This also applies to our BGM Superstrong 2.0 CR couplings. The old engine oil specification SAE30 corresponds to the current gear oil specification SAE 85W/90. As lubricant we recommend the BGM Pro Street gear oil (BGM2025, corresponds to specification API GL-3).
AI-translation
incl. VAT plus shipping costs
OEM numbers (for comparison purposes only) | |
---|---|
BGM | BGM8322 |
Customers alternatively searched for | |
---|---|
Kupplung | Typ Honda CR80 | CR | CR 80 | 110mm | Durchmesser | Ø=110mm |Kulu | Koppeling | Clutch | Schleuderbacken | Schleuderbackensatz | Kraftübertragung | Kupplungsrupfen | Kupplungsrutschen | Anfahren | Ruckeln | Anfahrruckeln | Durchgehen | Embrayage | Frizione | Embrague | |
Funktionale Cookies sind für die Funktionalität des Webshops unbedingt erforderlich. Diese Cookies ordnen Ihrem Browser eine eindeutige zufällige ID zu damit Ihr ungehindertes Einkaufserlebnis über mehrere Seitenaufrufe hinweg gewährleistet werden kann.
Marketing Cookies dienen dazu Werbeanzeigen auf der Webseite zielgerichtet und individuell über mehrere Seitenaufrufe und Browsersitzungen zu schalten.
Tracking Cookies helfen dem Shopbetreiber Informationen über das Verhalten von Nutzern auf ihrer Webseite zu sammeln und auszuwerten.
Diese Cookies werden genutzt zur Erhebung und Verarbeitung von Informationen über die Verwendung der Webseite von Nutzern, um anschließend Werbung und/oder Inhalte in anderen Zusammenhängen, in weiterer Folge zu personalisieren.
Service Cookies werden genutzt um dem Nutzer zusätzliche Angebote (z.B. Live Chats) auf der Webseite zur Verfügung zu stellen. Informationen, die über diese Service Cookies gewonnen werden, können möglicherweise auch zur Seitenanalyse weiterverarbeitet werden.