Write a review
Evaluations will be activated after verification.
Item successfully added.
Gasket kit Malossi 46.5mm- timing tuning kit- MC-Gasket- for Piaggio Ciao, Bravo, Si, Boxer with Malossi Sport 46.5mm cylinder
Part no.:
MC222209
Description
⭐️ MCGASKET 46.5 CAST FOR NEW MALOSSI CAST CYLINDER ⭐️
The all-in-one "timing tuning kit" from MCPROPARTS for the new Malossi 46.5 cast cylinder.
So it is possible to turn something on the timing screw
without sacrificing compression,
driving an unnecessarily high
pinch point,
or having to turn off / mill down the head.
Through the use of high quality material & alloy, as far as the sealing & pressure properties are concerned,
it is easily possible to drive a low pin ch
edge
without getting sealing problems.
In this case, a copper & aluminum alloy was used to make this possible.
The alloys have a better heat dissipation
than the original gaskets with a better pressure resistance.
In order to use / release e.g. the channels / ports completely at UT,
a thicker foot seal would be necessary, but you usually end up with a too high QK.
With the MCGASKET 46,5 Cast Kit it is possible to
optimize the timing as needed with
a low/usable squish edge.
Included in the kit :
1x foot gasket Malossi 46,5 cast cylinder (New Model) 0,40mm Alu 1x
foot gasket Malossi 46,5 cast cylinder (New Model) 0,50mm Alu 1x foot gasket Malossi 46,5 cast cylinder (New Model) 0,
60mm Alu 1x
head gasket Malossi 46,5 cast cylinder (New Model) 0,35mm Copper
1x head gasket Malossi 46,5 cast cylinder (New Model) 0,40mm Copper
It should be noted that because
the gaskets are very accurately made & the original after-simulated
, respectively with the original 1 to 1 from the dimensions match,
that also here, as with the original gaskets, if necessary at the holes for the studs must be reworked.
In the tests it was necessary with the head gasket one of the holes minimally with a round arrow to enlarge,
in connection with the following housings & Stud bolts :
- Polini Speed Engine housing with Malossi stud bolts
- Original housing (Italo Moped) with Malossi stud bol ts.
AI-translation
The all-in-one "timing tuning kit" from MCPROPARTS for the new Malossi 46.5 cast cylinder.
So it is possible to turn something on the timing screw
without sacrificing compression,
driving an unnecessarily high
pinch point,
or having to turn off / mill down the head.
Through the use of high quality material & alloy, as far as the sealing & pressure properties are concerned,
it is easily possible to drive a low pin ch
edge
without getting sealing problems.
In this case, a copper & aluminum alloy was used to make this possible.
The alloys have a better heat dissipation
than the original gaskets with a better pressure resistance.
In order to use / release e.g. the channels / ports completely at UT,
a thicker foot seal would be necessary, but you usually end up with a too high QK.
With the MCGASKET 46,5 Cast Kit it is possible to
optimize the timing as needed with
a low/usable squish edge.
Included in the kit :
1x foot gasket Malossi 46,5 cast cylinder (New Model) 0,40mm Alu 1x
foot gasket Malossi 46,5 cast cylinder (New Model) 0,50mm Alu 1x foot gasket Malossi 46,5 cast cylinder (New Model) 0,
60mm Alu 1x
head gasket Malossi 46,5 cast cylinder (New Model) 0,35mm Copper
1x head gasket Malossi 46,5 cast cylinder (New Model) 0,40mm Copper
It should be noted that because
the gaskets are very accurately made & the original after-simulated
, respectively with the original 1 to 1 from the dimensions match,
that also here, as with the original gaskets, if necessary at the holes for the studs must be reworked.
In the tests it was necessary with the head gasket one of the holes minimally with a round arrow to enlarge,
in connection with the following housings & Stud bolts :
- Polini Speed Engine housing with Malossi stud bolts
- Original housing (Italo Moped) with Malossi stud bol ts.
€23.95 *
incl. VAT plus shipping costs
Available immediately (delivery time 1-3 working days*)
P
For this item you get
fidelity point/s
| Customers alternatively searched for | |
|---|---|
| Dichtsatz | Zylinder | Zylinderdichtsatz | Zylinderdichtung | Kopfdichtung | Fußdichtung | Dichtung | Zylinderfuß | Zylinderkopf | Gasket | Set | Cylinder | Sealer | Covering | Sealing | Packing | Pochette De Joints Cylindre | Guarnizioni Kit Cilindro | Kit De Juntas Para Cilindro | Empaquetadura | 46,5 mm | 46.5 | 46.5 mm| MC | MCPROPARTS | mcproparts | |
Related items
Recently viewed items