Fixed face rear pulley -PIAGGIO- Vespa ET2 50 (ZAPC12000, ZAPC16000, ZAPC38100), Vespa ET4 50 50 (ZAPC26000, ZAPC26100), Vespa LX 50 (ZAPC38101, ZAPC38104, ZAPC38300, ZAPC38400, ZAPC38700, ZAPC38900), Vespa LXV 50 (ZAPC38102, ZAPC38902), Vespa Primavera 5

Pulley unit with clutch -PIAGGIO- Piaggio 50 cc Ø=134mm (since 2000)

Pulley -PIAGGIO- Vespa ET2 50 (ZAPC12000, ZAPC16000, ZAPC38100), Vespa ET4 50 50 (ZAPC26000, ZAPC26100), Vespa LX 50 (ZAPC38101, ZAPC38104, ZAPC38300, ZAPC38400, ZAPC38700, ZAPC38900), Vespa LXV 50 (ZAPC38102, ZAPC38902), Vespa Primavera 50 (ZAPC53100, ZA

Clutch -PIAGGIO- Vespa Primavera 50 (ZAPC53200), Vespa Sprint 50 (ZAPC53201, ZAPC53301, ZAPC53303), Gilera DNA 50 (ZAPC27000), Gilera Runner 50 (ZAPC14000, ZAPC36100, ZAPC36200, ZAPC36400, ZAPC46100, ZAPC46200, ZAPC46300), Gilera Storm 50 (ZAPC29000), Pia

Clutch bell -PIAGGIO- Piaggio/Gilera 50-100cc (2-stroke, 4-stroke), Peugeot 50cc, Honda 50cc, Kymco 50cc, SYM 50cc, GY6 (4-stroke) 50cc Ø=107mm

Contrast spring -PIAGGIO- Vespa ET2, ET4 50, LX 50, LXV 50, S 50, Primavera 50, Sprint 50, Piaggio Fly 50, Free 50-100, Liberty 50, NRG, NTT, Quartz, Sfera 50 RST, TPH 50, Zip SP, Zip II 50

Contrast spring support, clutch side -PIAGGIO- Piaggio 50cc 2-stroke/4-stroke

Needle roller bearing -HK 1718- (17x25x18mm) - (used for pulley Minarelli 50cc (type MA, MY, CW, CA, CY), Piaggio 50cc 2-stroke, Piaggio 50-100cc 4-stroke)

Ball bearing -6901 LU- (12x24x6mm)

Contrast spring support, drive side -PIAGGIO- Piaggio 50cc 2-stroke/4-stroke

Shaft seal ring -PIAGGIO- 34x39x3mm - for movable face rear pulley - Vespa GTS 125-150, 946 125-150, LX 50-150, LXV 50-150, S 50-150, Primavera 50-150, Sprint 50-150, ET2, Piaggio NRG, Free 50-100, Fly 50-125

O-ring for pulley -PIAGGIO- Vespa GTS 125 (ZAPMA3100, ZAPMA3200, ZAPMA3700, ZAPMD3200), Vespa GTS 150 (ZAPMA3200, ZAPMA3100), Vespa GTS Super 125 (ZAPMA3100, ZAPMA3200, ZAPMA3700, ZAPMD3200), Vespa LT 150 (RP8M66603), Vespa LX 125 (ZAPM68300, ZAPM68303),

Nut with serrated flange -DIN 6923- M10 x 1.25 (used for crankshaft (drive side) Piaggio 50cc, Minarelli 50cc)

Clutch nut -M28x1- wrench size 34mm

Pulley guide pin -PIAGGIO- Piaggio 50cc 2-stroke (except Sfera (NSL1T) and Zip (SSL1T)), Piaggio 50-100cc 4-stroke

Circlip -HOLE DIN472- Ø=24mm - (used for flywheel Vespa Wideframe VM, VB, VL, VNA, VBA, GS150 / GS3, GL)