EGIG PERFORMANCE intake manifold 220 ccm Ø34 mm straight version for Vespa Smallframe
Straight CNC intake manifold for EGIG 205, 210 and 220 cc setups with Ø34 mm passage and Ø40 mm connection width.
The EGIG PERFORMANCE intake manifold Ø34 mm is designed for Vespa Smallframe engines with EGIG 205, 210 or 220 cc cylinders and is aimed at setups with a correspondingly larger intake tract. The straight, CNC-milled aluminum design reduces the deflection in the intake path and can improve the flow compared to the curved intake. According to the manufacturer, up to 1.5 hp and 1.5 Nm advantage over the curved version is possible with the right engine tuning. A frame cut-out is required for installation.
EGIG PERFORMANCE
CNC aluminum
Ø34 mm passage
Ø40 mm connection width
Frame cut-out required
What makes the product special
Straight intake manifold for EGIG 205, 210 and 220 cc cylinders with reed valve intake
Ø34 mm passage for larger smallframe setups
Ø40 mm connection width including matching connecting rubber and hose clamps
CNC-milled aluminum contour for defined transitions in the intake tract
More flow-optimized solution compared to the curved version if the necessary installation space is created
Ø34 mm passage for larger intake cross-sections
The Ø34 mm version lies between the smaller Ø30 mm version and the large Ø39 mm version. It is suitable for EGIG 205, 210 and 220 cc engines where a larger intake cross-section is required without going directly to the largest passage variant. The tuning of carburetor, diaphragm, exhaust and timing remains decisive.
Straight version with clear frame requirement
Important installation note
The straight intake manifold does not fit into the smallframe frame without machining. The frame must be cut out for installation. If no frame machining is required, the conventional, curved intake manifold should be used.
Only for suitable EGIG cylinders
This intake manifold is not intended for standard Vespa cylinders or any tuning cylinders. It is designed for EGIG 205, 210 and 220 cc cylinders with diaphragm intake. Before installation, the connection width, rubber connection, carburetor position and space in the frame should be checked.
Scope of delivery
Scope of delivery according to the information provided
EGIG PERFORMANCE intake manifold, straight version
Suitable connecting rubber
Matching hose clamps
Connection rubber and hose clamps are included in the scope of delivery according to the additional information. Only include additional mounting accessories if they are listed separately in the item scope of delivery.
Suitable vehicle models
Vespa 50 / N V5A1T, 50 L V5A1T, 50 R V5A1T, 50 S V5SA1T, 50 Special V5A2T / V5B1T / V5B3T, 50 Special Elestart V5A3T / V5B2T / V5B4T, 50 SR / Sprinter V5SS2T, 50 SS / Super Sprint V5SS1T. Only with EGIG 205 / 210 / 220 cc cylinder and adapted frame.
Vespa 90 V9A1T, 90 Racer V9SS2T, 90 SS Super Sprint V9SS1T, 100 Sport V9B1T, Vespa 125 VMA1T, 125 Primavera VMA2T and 125 Primavera ET3 VMB1T. The actual fit depends on the EGIG cylinder, engine housing and frame cut-out.
Motovespa 75 / 125 Primavera models can be relevant with the corresponding EGIG engine design, but must be checked before fitting. Spanish Motovespa models may differ in terms of frame, intake area and engine housing depending on the year of manufacture and market version.
Brief technical overview
| Manufacturer | EGIG PERFORMANCE |
|---|
| Engine type | Intake manifold / intake manifold for diaphragm intake |
|---|
| Version | Straight version |
|---|
| material | CNC-milled aluminum |
|---|
| Passage | Ø34 mm |
|---|
| Connection width | Ø40 mm |
|---|
| Suitable for | EGIG 205 / 210 / 220 ccm cylinder |
|---|
| Vehicle base | Vespa PV125, ET3 and other Vespa Smallframe models with the corresponding EGIG engine design |
|---|
| Scope of delivery | Intake manifold, matching connecting rubber and hose clamps |
|---|
| Fitting instructions | Frame cut-out required, otherwise use curved intake manifold |
|---|
| Special feature | Straight intake path, according to the manufacturer up to 1.5 hp and 1.5 Nm advantage over curved version possible |
|---|
Conclusion
The EGIG PERFORMANCE intake manifold Ø34 mm is the middle straight version for EGIG 205, 210 and 220 cc smallframe engines. It combines a larger passage with more direct intake routing, but requires deliberate frame machining.
FAQ
It is intended for EGIG 205, 210 and 220 cc cylinders with diaphragm intake.
No. The straight version requires a frame cut-out. Without this machining, the curved intake manifold is the more sensible choice.
The connection width describes the area for the rubber connection to the rest of the intake system. It must match the rubber and carburetor connection used.
Not automatically. The appropriate passage depends on the entire setup. Carburetor, diaphragm, exhaust, timing and tuning must fit together.
DE | €
